CANNAFLOORS FAST PATCH
CANNAFLOORS Fast Patch is a two component, high strength, extremely fast curing concrete patching system. It’s advanced formula allows the user to quickly rebuild damaged control joints, spalls, and large cracks, even in low tempurature. Because of its physical properties and high load-bearing strength, it is the right choice for filling prior to the application of all CANNAFLOORS systems.
ADVANTAGES
• 0 VOC
• Self-priming
• Stainable
• Easy Mixing
• Low Temperature Cure
• Vertical Applications
• Rapid Cure (20-30 Minutes)
• Moisture resistant
• Chemical resistant
• Withstands heavy traffic
• Grind 20 minutes or less
• Meets USGBC LEED criteria IEQ4.1
APPLICATIONS
• Rebuild control joints
• Bond cracked slabs
• Cold rooms
• Leveling Transitions
• Rapid repairs prior to coating
• Concrete polish
PACKAGING
CANNAFLOORS is available in two different kit sizes:
| CANNAFLOORS Kit Sizes | Part A | Part B |
|---|---|---|
| 1 Gallon Kit | 1/2 gal. | 1/2 gal. |
| 8 Gallon Kit | 4 gal. | 4 gal. |
COLORS
CANNAFLOORS Fast Patch is available in Gray
CONCRETE PREPARATION
Before coating is applied, concrete must be:
• Dry - No wet areas
• Clean - Contaminants removed
• Profiled - Surface sanded and loose splinters removed.
Mechanical preparation is the method of preparing concrete for coating application. Shot-blasting or diamond grinding are acceptable methods. Use a crack chaser with a diamond blade to prepare joints and cracks prior to installation of CANNAFLOORS Fast Patch.
PRODUCT DATA
| PROPERTY | VALUE |
|---|---|
| Volumetric Ratio | 1 to 1 |
| Solids | 100% (+ or - 1%) |
| Application Temperature | 28-75°F and 5° above dew point |
| Thinning | Not required |
| Pot Life | Approx 1 1/2 minutes |
| Cure Time | 20-30 minutes |
| Shelf Life | 12 months (unopened) |
| Hardness (ASTM D 2240) | Shore 57-60D |
| Tensile Strength (ASTM D2240) | 4600 psi |
| Elongation % (ASTM 412) | 6% - 8% |
| Compressive Strength (neat) | 3900 psi |
| Compressive Strength (with sand) (ASTM C109) | 4800 psi |
| Bond Strength (ASTM 882-99) | 3550 psi |
MIXING
The ratio of CANNAFLOORS Fast Patch is 1 to 1. That is, 1 part A (resin) to 1 part B (hardener). Mix with a paint stick, trowel, or tapers knife. Fast Patch material cures quickly. Mix small batches to optimize working time.
1. Mix equal amounts of part A and part B together for 30 seconds. Mix only the amount of meterial that can be applied within 1-2 minutes.
2. Immidiate apply to concrete.
3. If mixing with sand as a mortar/slurry. Mix A and B first and then add sand. Mix for another 20 seconds and apply immediately
APPLICATION INSTRUCTIONS
Clean the area of debris and contaminants that would act to debond CANNAFLOORS Fast Patch; oils, loose materials, dirt, rubber, etc. Expose clean rough concrete for best results. If using a saw to cut concrete and clean the crack, remove al of the dust from the cut out area. Cut a vertical edge, minimum 1/4" deep, around the perimeter of spal. Make sure the area is dry. Vacuum al cement dust.
Apply Fast Past with a 3"x8" trowel or tapers knife.
CLEAN-UP
CANNAFLOORS Fast Patch, while in an un-reacted state, may be cleaned up with water and degreaser. Isopropyl alcohol or acetone may be needed once the resin begins hardening.
WARRANTY
CANNAFLOORS products are warranted for one year after date of application. Please refer to the CANNAFLOORS Limited Material warranty for additional clarification.
SAFETY
Consult CANNAFLOORS Fast Patch Safety Data Sheet. Avoid Fast Patch contact with skin. Some individuals may be allergic to resin. Protective gloves, clothing, and mask are recommended.