CANNAFLOORS FAST PATCH (CARTRIDGE)
CANNAFLOORS Fast Patch is a two component, high strength, extremely fast curing concrete patching system. It’s advanced formula allows the user to quickly rebuild damaged control joints, spalls, and large cracks, even in low tempurature. Because of its physical properties and high load-bearing strength, it is the right choice for filling prior to the application of CANNAFLOORS coating system. CANNAFLOORS Fast Patch is specially formulated tocure for vehicle traffic in 20 to 30 minutes.
ADVANTAGES
• 0 VOC
• Self-priming
• Stainable
• Easy Mixing
• Low Temperature Cure
• Low Smell
• Rapid Cure (20-30 Minutes)
• Moisture resistant
• Chemical resistant
• Withstands heavy traffic
• Grind 20 minutes or less
• Meets USGBC LEED criteria IEQ4.1
APPLICATIONS
CANNAFLOORS Fast Patch can be used for rapid repair of cracks, spalls, and holes in concrete, and the following applications:
• Rebuild control joints
• Bond cracked slabs
• Cold rooms
• Grade matching
• Rapid repairs prior to coating
• Cracks in concrete
PACKAGING
CANNAFLOORS Fast Patch is available in one kit size:
| Part A | Part B | |
|---|---|---|
| 22oz Caulking Cartridge: | 11 oz. | 11 oz. |
COLORS
CANNAFLOORS Fast Pacth is available in Gray
PRODUCT DATA
| PROPERTY | VALUE |
|---|---|
| Volumetric Ratio | 1 to 1 |
| Solids | 100% (+ or - 1%) |
| Application Temperature | 28-75°F and 5° above dew point |
| Thinning | Not required |
| Pot Life | Approx 1 1/2 minutes |
| Cure Time | 20-30 minutes |
| Shelf Life | 12 months (unopened) |
| Hardness (ASTM D 2240) | Shore 57-60D |
| Tensile Strength (ASTM D 2240) | 4600 psi |
| Elongation % (ASTM 412) | 6% - 8% |
| Compressive Strength (neat) | 3900 psi |
| Compressive Strength (with sand) (ASTM C109) | 4800 psi |
| Bond Strength (ASTM 882-99) | 3550 psi |
CONCRETE PREPARATION
Before coating is applied, concrete must be:
• Dry - No wet areas
• Clean - Contaminants removed
• Profiled - Surface sanded and loose splinters removed.
Mechanical preparation is the method of preparing concrete for coating application. Shot-blasting or diamond grinding are acceptable methods. Use a crack chaser with a diamond blade to prepare joints and cracks prior to installation of CANNAFLOORS Fast Patch.
APPLICATION INSTRUCTIONS
Clean the area of debris and contaminants that would act to debond CANNAFLOORS Fast Patch; oils, loose materials, dirt, rubber, etc. Expose clean rough concrete for best results. If using a saw to cut concrete and clean the crack, remove al of the dust from the cut out area. Cut a vertical edge, minimum 1/4" deep, around the perimeter of spal. Make sure the area is dry. Vacuum al cement dust.
Caulking Cartridge Application: Remove end cap from cartridge.Screw static mixer to top of cartridge. Place assembled cartridge into pneumatic dispensing tool for use. Extrude a smal amount of material off to the side until a uniform color is achieved. Dispense under a constant uniform pressure.
CANNAFLOORS Fast Patch requires diamond grinding after it has cured. This should be performed prior to the application of any CANNAFLOOR system. If CANNAFLOORS Fast Patch is not ground, it may be seen through the new coating system.
CLEAN-UP
CANNAFLOORS Fast Patch, while in an un-reacted state, may be cleaned up with water and degreaser. Isopropyl alcohol or acetone may be needed once the resin begins hardening.
WARRANTY
CANNAFLOORS products are warranted for one year after date of application. Please refer to the CANNAFLOORS Limited Material warranty for additional clarification.
SAFETY
Consult CANNAFLOORS Fast Patch Safety Data Sheet. Avoid Fast Patch contact with skin. Some individuals may be allergic to resin. Protective gloves, clothing, and mask are recommended.