CANNAFLOORS PREMIUM POLYASPARTIC
CANNAFLOORS Premium Polyaspartic is a two component, pigmented polyaspartic. It is formulated to withstand continuous cleanings, harsh chemicals, extreme UV exposure, & wet enviroments. CANNAFLOORS Premium Polyaspartic is the ideal product to use to give your floors a strong scratch and chemical resistant surface while maintaining a high gloss, easy to clean finish.
ADVANTAGES
• Abrasion resistant
• Non-yellowing
• Chemically resistant
• Low VOC
• Easy mixing Ratio (1:1)
• Flexible
• High Gloss Finish
• FDA/USDA Approved
COLORS
CANNAFLOORS Premium Polyaspartic is available in the fo lowing colors. Please contact a CANNAFLOORS Sales Represenative for additional available colors.
• Light Gray
• Medium Gray
• White (Requires 2 coats)
APPLICATIONS
• Cultivation
• Manufacturing
• Distribution
• Indoor / Exterior
• Production
PACKAGING
CANNAFLOORS is available in two different kit sizes:
| CANNAFLOORS Kit Sizes | Part A | Part B |
|---|---|---|
| 2 Gallon Kit | 1 gal. | 1 gal. |
| 10 Gallon Kit | 5 gal. | 5 gal. |
CONCRETE PREPARATION
Before coating is applied, floor must be:
• Dry – No wet areas
• Clean – Contaminants removed
TESTING
All surfaces are not the same. It is recommended that a sample area be done before the start of the project. The test should be done on-site, using the proposed method by the assigned applicator to insure proper adhesion and color. A sample area should also be done on any existing coatings to determine if any contaminants exist or if delaminating will occur.
PHYSICAL PROPERTIES
| PROPERTY | VALUE |
|---|---|
| Appearance | Clear Liquid |
| Total Solids (% by Weight) | 85 |
| Total Solids (% by Volume) | 85 |
| Surface Tension, Dynes/cm | 40 |
| Viscosity (Brookfield LVF), cps @ 25° C | 600 |
| Density (lbs/gallon) | 8.32 |
| Specific Gravity | 1.0 |
| Flash Point (C Pensky-Martens closed cup) | <70 |
| Freeze/Thaw Stability | N/A |
| Thermal Stability (28 days @ 52° C) | No Effect |
| Mechanical Stability | Good |
| VOC (g/l) | > 50 g. per liter |
| VOC (by Weight) | > 50 g. per liter |
| Tg (C) | 66 |
| Tensile Strength, psi | 7000 |
| Elongation | 8% |
FILM PROPERTIES
PHYSICAL PERFORMANCE PROPERTIES OF DRY FILM
All tests were conducted on 2.0 to 2.5 mil films, and air-dried for seven days at room temperature.
| PROPERTY | VALUE |
|---|---|
| Hardness (Pencil / Sword) | 2H / 70 |
| Taber Abrasion | 90 (mg loss per 1000 cycles, CS-17 wheel, 1000 load) |
| Impact Resistance | 140 / 140 (lbs) (Direct / Reverse) |
| Crosshatch Adhesion | 100% / 100 (Untreated Cold Rolled Steel / Untreated Aluminum) |
PATCHING
Voids, cracks and imperfections will be seen in finished coating if the concrete is not patched correctly. After the patching material is cured, diamond grind patch.
CLEAN-UP
CANNAFLOORS Premium Polyaspartic, while in an un-reacted state, may be cleaned up with water and degreaser. Isopropyl alcohol or acetone may be needed once the resin begins hardening. Lastly, a strong solvent like methylene chloride may be required ifresin is nearly set up.
CHEMICAL RESISTANCE: 7-DAY SUBMERSION
| PROPERTY | VALUE |
|---|---|
| Brake Fluid | No Effect |
| Transmission Fluid | Slight Discoloration |
| Coolant | No Effect |
| Power Steering Fluid | Slight Discoloration |
| Battery Acid | Damaged |
| MEK | <200 Double Rubs |
| Acetone | <200 Double Rubs |
| Formula 409 | <200 Double Rubs |
PRODUCT DATA
| PROPERTY | VALUE |
|---|---|
| Volumetric Ratio | 1 to 1 |
| Coverage | 400-500 SF/Gal |
| Application temperature | 60-90°F |
| Thinning | Not required |
| Pot life | 15-20 minutes |
| Working time on floor | 15-20 minutes |
| Cure time | 6-8 hours |
| Critical recoat time | 24 hours |
| Shelf life | 12 months |
| USDA Food & Beverage | Meets requirements |
APPLICATION
1. Always apply in descending temperatures. Concrete is porous and traps air. In ascending temperatures (generally mornings) the air expands and can cause out gassing in the coating. It is safer to apply coatings in the late afternoon, especially for exterior applications.
2. Optimumambient temperature should be between 65- 90°F during application.
3. Mix CANNAFLOORS Premium Polyaspartic using mixing instructions found on this TDS.
4. Apply approximately 400-500 SF per gallon by immediately pouring out on surface in a ribbon, whilewalking and pouring at the same time until bucket is empty.
5. Using a squeegee on a pole, pull CANNAFLOORS over substratewhile uniformly covering surface.
6. Using a 3/8” non-shedding phenolic (plastic) core paint roller,roll coating forwards and backwards.
7. Lastly, back roll in the opposite direction as step 6.
MIXING
The ratio of CANNAFLOORS Premium Polyaspartic is 1 to 1. That is, 1 part A (resin) to 1 part B (hardener).
Generally, 2 mixed gallon of CANNAFLOORS Polyaspartic is ideal for application. Mix the following with a drill and mixing paddle. Note: If using a drill mixer, use a low speed to prevent air entrapment.
1. Pour out 1 gallon of Part A into a clean bucket.
2. Add 1 gallon of Part B and mix for 2 minutes.
PRODUCT LIMITATIONS
Coating systems are susceptible to cracking if the concrete moves or separates below the coating. Hence, joint and crack treatment should be reviewed prior to coating application. As a general rule, control joints (saw cuts) and random cracks should be saw-cut or chased first then filled with Patch.
SAFETY
Consult CANNAFLOORS Premium Polyaspartic Safety Data Sheet. Avoid CANNAFLOORS contact with skin. Some individuals may be allergic to polyaspartic resin and isocyanate. Protective gloves, clothing, and mask are recommended.
WARRANTY
CANNAFLOORS products are warranted for one year after date of application.
Please refer to the CANNAFLOORS Limited Materialwarranty for additional clarification.