CANNAFLOORS URETHANE CEMENT

CANNAFLOORS Urethane Cement is a three component polyurethane concrete floor coating system. It is specially formulated for Cannabis facilities. CANNAFLOORS Urethane Cement is a seamless antimicrobial flooring that is FDA & USDA approved for application in cannabis facilities to withstand the harsh humid climates and the constant changing in temperature. It is 100% solids that allows vapor release, so the moisture drawn to the surface can expel and not cause damage to the bond resulting in flooring failures.

TDS Form

Mixing Instructions

ADVANTAGES

• Low odor
• Abrasive resistant
• -20° to 230° F temperature range
• UV stable
• Handles severe impact conditions
• Highly Chemical Resistant
• Seamless flooring system
• Withstands Heavy Forklift Traffic
• Resistant to thermal shock

APPLICATIONS

• Cultivation
• Manufacturing
• Distribution
• Indoor / Exterior
• Production

COLORS

CANNAFLOORS Urethane Cement is available in the following color packs. Custom color packs can be developed at an additional charge.

• Light Gray
• Medium Gray
• White

Note: White requires 2 coats of Polyasaprtic Top Coat

MIXING

The ratio of CANNAFLOORS Urethane Cement is pre measured and no volumetric mixing is needed. Use a drill and mixing paddle to mix the following. Note: If using a drill mixer, use a low speed (not to exceed 300 rpm) to prevent air entrapment.

1. Pour Pre-Measured A and B containers in 5 Gallon pail.
2. Mix A and B parts for 1 minute.
3. Next Slowly add 1 Part C powder bag under gitation.
4. Mix all 3 parts for 2 minutes.

Note: To Ensure proper and consistent mixing, scrape walls of mixing vessels while mixing to achieve uniform mix.

INSTALLATION

1. Apply properly mixed material on the floor, pouring the entire contents of bucket in a long continuous bead.
2. Using a notch squeegee at the desired setting, rake material evenly.
3. Immediately back roll wet material with a 3/8" Nap roller. Back-rolling removes any unevenness left by the rake and breaks surface tension. This generally requires the user to wear spiked shoes, allowing him to walk in the wet resin mix.
4. Remember to keep a wet edge by bringing a continuous supply of newly mixed material to the area being coated.

CLEAN-UP

CANNAFLOORS UC, while in an un-reacted state, may be cleaned up with water and Degreaser. Isopropyl alcohol or acetone may be needed once the resin begins hardening. Lastly, a strong solvent like xylene may be required if resin is nearly set up.

PACKAGING

CANNAFLOORS Urethane Cement is available in one kit

Size: Part A/ Part B, Part C(Powdered Filler), Color Pack

Unit 1 Kit: Pre-measured, 1 bag/pail, 1 pack

PRODUCT DATA

  
        Volumetric Ratio
        Pre-Measured Kits
      
        Solids
        100% (+ or - 1%)
      
        Coverage
        200-300 sqft
      
        Application temperature
        60-90°F
      
        Thinning
        Not required
      
        Pot life
        10-15 minutes
      
        Working time on floor
        20-30 minutes
      
        Cure time
        10-12 hours (walking) 24-48 hours (traffic)

PHYSICAL PROPERTIES

  
        PROPERTY
        VALUE
        REFERENCE
      
        Compressive Strength
        8,200 psi
        ASTM C 579
      
        Flexural Strength
        2,375 psi
        ASTM C 580
      
        Tensile Strength
        920 psi
        ASTM C 307
      
        Bond to Concrete
        350 psi
        ASTM C 478
      
        Concrete fails at this point
      
        Coefficient of Thermal
        
        Expansion
        < 12.6 X 10-6 >
         C-531
      
        Water Absorption
        .10% Max.
        ASTM D 570
      
        Linear Shrinkage
        .20% Max
        ASTM C 531
      
        Impact Resist. 16 ft.lb
        No failure
        Mil-D-3134F
      
        Anti-Microbial
        Passes
        G-21
      
        Coefficient of Friction
        Pass
        ASTM D 2047
      
        Modules of Elasticity
        1.8 X 105
        
        Temperature Rating
        230° F

SAFETY

Consult CANNAFLOORS Urethane Cement safety data sheet. Avoid Urethane Cement contact with skin. Some individuals may be allergic to urethane and isocyanates. Always wear protective gloves, eye wear and clothing.

PRODUCT LIMITATIONS

Coating systems are susceptible to cracking if the
concrete moves or separates below the coating.
Hence, joint and crack treatment should be reviewed prior to coating application. As a general rule, control joints (saw cuts) and random cracks should be saw-cut or chased first then filled with Patch. Construction/cold joints (two slabs which meet and hence move) should be treated.

WARRANTY

CANNAFLOORS products are warranted for one year after date of application.

Please refer to the CANNAFLOORS Limited Material warranty for additional clarification.